The Brain Gate Neural Interface System is grounded on Cybernetics podium technology to sense, transmit, analyse and apply the language of neurons. The System consists of a sensor that is entrenched on the motor cortex of the brain and examines brain signals. The principle behind the Brain Gate system is that, signals are generated in the motor cortex and they cannot be sent directly to the arms, hands and legs due to spinal cord injury, stroke or other condition. Download Seminar Report for Braingate System...
In this project we have devised a robot which will move from any position in a m*n maze to any target point detecting the obstacles in the way. Our robot acts according to a code written purely in C language, which directs it to explore the maze containing random obstacles. The robot is totally controlled by the computer by Interfacing it with a computer, using Parallel Port. Download Seminar Report for Maze Solving Robot...
Air powered cars runs on compressed air instead of gasoline. This car is powered by a two cylinder compressed engine. This engine can run either on compressed air alone or act as an IC engine. Compressed air is stored in glass or fiber tanks at a pressure of 4351 psi. Within the next two years, you could see the first air-powered vehicle motoring through your town. Most likely, it will be the e.Volution car that is being built by Zero Pollution Motors. Download Seminar Report for Air powered cars...
Automatic Dependent Surveillance Broadcast (ADS-B) is an air traffic surveillance technology that enables aircraft to be accurately tracked by air traffic controllers and other pilots without the need for conventional radar. While the initial application of ADS-B is to provide high quality surveillance for air traffic control, it also facilitates a number of advanced air-to-air applications that will in future significantly improve safety and performance of aircraft operations. Download Seminar Report for Automatic Dependent Surveillance (ADS-B)...
Increasingly, network applications must communicate with counterparts across disparate networking environments characterized by significantly different sets of physical and operational constraints; wide variations in transmission latency are particularly troublesome. The proposed Interplanetary Internet (IPN), which must encompass both terrestrial and interplanetary links, is an extreme case. Download Seminar Report for Delay Tolerant Networks...
Each mobile uses a separate, temporary radio channel to talk to the cell site. The cell site talks to many mobiles at once, using one channel per mobile. Channels use a pair of frequencies for communication. One for transmitting from the cell site, the forward link, and one frequency for the cell site to receive calls from the users, the reverse link. Download Seminar Report for Mobile Train Radio Communication...
Hy-Wire car is without hydraulic and mechanical linkage end engine. Instead of these it contains a fuel cell stack and a drive by wire system. It is fully automated future car. In future it will have a wide application. The problem with fuel consumption and pollution can be minimize to certain level. Two basic elements largely dictate car design today: the internal combustion engine and mechanical and hydraulic linkages. If you have ever looked under the hood of a car, you know an internal combustion engine requires a lot of additional equipment to function correctly. Download Seminar Report for Hy Wire Car...
Hyper Transport technology is a very fast, low latency,? point-to-point link used for inter-connecting integrated circuits on board. Hyper Transport, previously codenamed as Lightning Data Transport (LDT), provides the bandwidth and flexibility critical for today's networking and computing platforms while retaining the fundamental programming model of PCI. Hyper Transport was invented by AMD and perfected with the help of several partners throughout the industry. Download Seminar Report for Hyper Transport Technology...
This Project Automatic Room Light Controller with Visitor Counter using Microcontroller is a reliable circuit that takes over the task of controlling the room lights as well us counting number of persons/ visitors in the room very accurately. When somebody enters into the room then the counter is incremented by one and the light in the room will be switched ON and when any one leaves the room then the counter is decremented by one. The light will be only switched OFF until all the persons in the room go out. Download Seminar Report for Automatic Room Light Controller...
The G200 has 4 main landing gear tires and two nose landing gear tires. The landing gear is tricycle type with two wheels on each gear strut. Each unit retracts into its? own well and is fully covered by doors, mechanically connected to the landing gear. Landing gear extension and retraction time is 9 ? 1 seconds. In emergency, landing gear may be extended by compressed nitrogen. Download Seminar Report for Landing Gear...
Asynchronous Transfer Mode (ATM) technology is capable of transferring voice, video, and data through private and public networks. It is built on a cell-based architecture rather than on a frame-based architecture. ATM cells are always a fixed length of 53 bytes. The ATM cell contains a 5 byte ATM header followed by 48 bytes of ATM payload. Small, fixed-length cells are well suited for carrying voice and video traffic because this traffic is intolerant of delay. Video and voice traffic do not have to wait for a larger data packet to be transmitted. Download Seminar Report for Asynchronous Transfer Mode...
Intelligent Transportation Systems help meet the transportation challenges: A broad range of diverse technologies, known collectively as intelligent transportation systems (ITS), holds the answer to many of our transportation problems. ITS is comprised of a number of technologies, including information processing, communications, control, sand electronics. Joining these technologies to our transportation system will save lives, save time, and save money. Download Seminar Report for Intelligent Transportation System...
Stealth is the technique of making a plane (or any other object) less visible to the enemy by reducing its radar and IR (infra red, heat) visibility. Reducing the IR image of a plane can be accomplished by directing the hot exhaust gasses to the top of the plane and mix them with cold air (the B-2 uses this technique). Reducing radar visibility can be accompli^ed by deflecting the radar waves in such a direction that they don't go back to the emitting radar (F-117 uses faceting, the B-2 uses continues curving) or making use of less radar reflecting materials (composite material, plastic) and/or radar absorbing coatings. Download Seminar Report for Stealth Technology...
Plastic welding and spot welding - both are almost similar to each other. There is a difference noted. In plastic welding, heat is supplied through convection of the pincher tips, instead of conduction. The two plastic pieces are brought together. At the time of welding, a jet of hot air is liberated. This melts the parts to be joined along with the plastic filler rod. Download Seminar Report for Plastic Welding...
This report examines tribology, the science of erosion and wear. More precisely focuses on the effect of erosion and wear on aircraft structures, as it is an important and costly aspect of the aeronautics industry. It looks at the three main areas that make up tribology: friction, wear, and lubrication, and the effect these have on aircraft structures. It examines the mechanisms of erosion and wear; that is the analytic science behind tribology. Download Seminar Report for Tribology...
Purpose of the grounding system is the connecting parts of electrical equipment which in normal circumstances is not energized. The purpose is to limit the voltage earthing system on parts of the equipment that is not energized and between these parts with the ground, so that was reached a safe value for all operating conditions. Download Seminar Report for Grounding System...
Direct torque control (DTC) of an induction motor fed by a voltage source inverter is a simple scheme that does not need long computation time, can be implanted without mechanical speed sensors and is insensitive to parameter variations. In principle, the motor terminal voltages and currents are sampled and used to estimate the motor flux and torque. Based on estimates of the flux position and the instantaneous errors in torque and stator flux magnitude, a voltage vector is selected to restrict the torque and the flux errors within their respective torque and flux hysteresis bands. Download Seminar Report for Direct Torque Control...
Tags :
